TECHNIAHQROBOT / INDEPENDENT ROBOTICS REPORTINGENGLISH EDITION / 12 November 2026
ROBOTICS / OPEN PROJECTResearch Platforms

UCSD Continuum Robot Actuation: Printable Modules and Assembly

UC San Diego's Morimoto Lab publishes a modular actuation platform for continuum and other high-degree-of-freedom robots. The repo contains mechanical CAD, 3D print files, a parts spreadsheet and an illustrated assembly PDF. The system is meant to be configured for a particular robot rather than treated as a complete general-purpose arm.

Editorial source check · Project documentation and public files; no physical test claimedRevision and parts availability may change
THE TECHNICAL DOSSIERUnified Continuum Robot Actuation

What the open hardware is for

The project demonstrates a reconfigurable actuator bank with channels for tendon-driven continuum robots. An optional central working channel can accommodate instruments or cameras depending on the configuration.

Different robots require different numbers of channels, cable routes, end-effector mountings and control policies. The official example should be treated as one mechanical reference.

A documented fabrication package

The repository lists a step-by-step assembly PDF, an Excel BOM, SolidWorks source models and printable parts. A linked full assembly video shows the order of physical components.

Separate printed mechanisms from purchased motors, screws, bearings and cable hardware in your cost estimate. Printed geometry does not replace actuation and sensing hardware.

Commissioning and limits

Before tensioning cables, measure the neutral length and joint workspace of the attached continuum robot. Drive each module separately and inspect tendon friction or slipping.

The source repository does not supply a universal teleoperation or force-control performance number across different robot geometries.

02 / FABRICATION AND ASSEMBLY

Modular continuum-actuation fabrication and wiring

Use matching revisions of parts, firmware and instructions. These steps summarize project documentation; no physical build was performed for this article.

Assembly sequence 5 steps

  1. Define the desired actuator channel count

    Identify how many tendon or other channels the robot needs before printing a reference bank.

    Manufacturer's instructions ↗
  2. Download the matched CAD and BOM

    Use the versioned repository assets and the official spreadsheet for printed and purchased parts.

    Manufacturer's instructions ↗
  3. Print and inspect the modules

    Check bearings, shafts, cable paths and motor mounts using the source mechanical model.

    Manufacturer's instructions ↗
  4. Assemble against the official video

    Install motors and transmission components in the documented order.

    Manufacturer's instructions ↗
  5. Integrate and test one channel

    Apply low load, inspect tendon routing and tension, then integrate the full manipulator carefully.

    Manufacturer's instructions ↗
03 / PRACTICAL QUESTIONS

Tendon channels, print files and component lists

Answers are based on published source material and project documentation. Their order does not represent search volume.

01Is this a complete robot I can print and deploy?

No. It is a modular actuator platform intended for use inside a larger continuum robot or other high-DOF assembly.

Sources Official project documentation ↗

02Are STL and SolidWorks files available?

The official hardware repository publishes both CAD and printable parts alongside the assembly documentation.

Sources Official project documentation ↗

03Where is the bill of materials?

The repository links an Excel parts list. It is intended for sourcing the actuation modules rather than a complete application-specific robot.

Sources Official project documentation ↗

04How do I assemble the modules in the right order?

Use the official step-by-step PDF with the full actuation-assembly video; their illustrations show orientation and subassembly sequence.

Sources Official project documentation ↗

05Will the sample layout fit any continuum robot?

No. The lab describes a reconfigurable design. Channel count, tendon paths and mechanical interfaces must be chosen for the target robot.

Sources Official project documentation ↗

06What are the design's reuse rights?

The lab publishes its CAD, print files and assembly materials under the MIT license. Check separate software packages before assuming their terms match.

Sources Official project documentation ↗

04 / ENGINEERING NOTES

What to check before building Unified Continuum Robot Actuation

Build and integration

Begin by choosing the number of driven channels and the mechanical route required by the target continuum robot. Compare that configuration with the included BOM and SolidWorks files, print the module components, source motors and hardware, then follow the assembly PDF alongside the manufacturer's full build video.

Known constraints

This is an actuation platform rather than a standalone autonomous robot. The repository does not establish that its example configuration fits every catheter, continuum manipulator or research arm. Electrical setup, tendon routing and software-specific control must be verified for each application.

05 / SOURCES

Original documentation

  1. Assembly video and project overview

Found a changed specification? Submit a correction with its source ↗

← Back to the open-source index