TECHNIAHQROBOT / INDEPENDENT ROBOTICS REPORTINGENGLISH EDITION / 12 November 2026
ROBOTICS / OPEN PROJECTRobot Hands

LEAP Hand V1: 16-Motor CAD, STLs, Wiring and Calibration

LEAP Hand V1 is an anthropomorphic research hand with sixteen Dynamixel motors. The official website provides left/right mechanical assemblies, individual STL and STEP downloads, a build sequence and software for Python, C++ and ROS. The mechanical CAD carries a noncommercial license even though the API source is MIT.

Editorial source check · Project documentation and public files; no physical test claimedRevision and parts availability may change
THE TECHNICAL DOSSIERLEAP Hand V1

Choose the left or right mechanical assembly

LEAP's CAD page provides separate right and left assemblies and individual printed-part downloads. Palm, cable spacers, MCP brackets and DIP spacers are listed with quantities, along with URDF and STEP assemblies.

Some mounting-plate STL variants match particular robot arms; select one that corresponds to your wrist interface, rather than printing all top plates.

One hand, sixteen motor IDs

The official V1 assembly divides each finger into motorized joints. Its published mapping uses IDs 0–3 for the index, 4–7 for middle, 8–11 for ring and 12–15 for the thumb.

The motor horns must be mounted in their documented home position. A mechanical offset cannot be corrected safely by guessing a larger software command.

Communication and overload troubleshooting

The V1 API expects a powered Dynamixel chain and USB connection. The project recommends inspecting the serial port with Dynamixel Wizard, then closing Wizard before starting the API to avoid a busy port.

The software repository documents jitter, missing motors and overload errors. These are addressed through horn orientation, correct IDs, cable paths, motor current limits and PID settings.

02 / FABRICATION AND ASSEMBLY

LEAP Hand V1 parts and sixteen motor IDs

Use matching revisions of parts, firmware and instructions. These steps summarize project documentation; no physical build was performed for this article.

Assembly sequence 5 steps

  1. Pick one handedness

    Download the matching palm and finger models and a mounting plate compatible with your arm.

    Manufacturer's instructions ↗
  2. Print and clean all plastic parts

    Check screw holes, supports and tendon-free pathways before attaching the Dynamixels.

    Manufacturer's instructions ↗
  3. Set home orientation

    Use the official horn reference to mount every finger joint correctly, then build all four fingers.

    Manufacturer's instructions ↗
  4. Assign the sixteen motor IDs

    Follow the V1 numbering table and wire the serial bus with the recommended power supply.

    Manufacturer's instructions ↗
  5. Run first commands

    Confirm servo enumeration, start low-current joint movements and monitor overload or oscillation.

    Manufacturer's instructions ↗
03 / PRACTICAL QUESTIONS

Serial ports, overloads and CAD permissions

Answers are based on published source material and project documentation. Their order does not represent search volume.

01Where are the printable STL files for LEAP Hand V1?

The official CAD page lists left and right palms, brackets, spacers and top plates as STL and STEP files. Choose parts for one mechanical version.

Sources Official project documentation ↗

02How many motors and what are their IDs?

V1 has 16 Dynamixel joints. The official assembly maps finger IDs in blocks of four: 0–3, 4–7, 8–11 and 12–15.

Sources Official project documentation ↗

03What if a finger is 90 degrees away from its home pose?

Check the actuator horn orientation first. The API troubleshooting guide says a horn may be mounted at the wrong angle.

Sources Official project documentation ↗

04Why does the Python API report a busy port?

Close Dynamixel Wizard before running Python because both cannot own the same serial port at once. Also verify the selected device name.

Sources Official project documentation ↗

05What causes hand jitter or overload?

The V1 SDK recommends adjusting PID gains and respecting current limits. Check mechanical binding before increasing controller gains.

Sources Official project documentation ↗

06Can I sell a hand using LEAP CAD?

The hardware CAD is under CC BY-NC-SA, which restricts commercial use. The API's MIT license does not replace the CAD terms.

Sources Official project documentation ↗

04 / ENGINEERING NOTES

What to check before building LEAP Hand V1

Build and integration

Choose left or right hand and download matching palm and finger files from the official CAD page. Identify each motor and its home orientation before mounting brackets. Assemble fingers and thumb according to the official pictures, then prepare power and USB communication. Map motor IDs in Dynamixel Wizard and start with low-current, low-speed checks.

Known constraints

Do not combine V1 geometry with LEAP Hand V2/V2 Advanced wiring without checking interfaces. Each of sixteen motors has an assigned ID and horn home position; mismatches can lead to a wrong pose. V1 CAD carries CC BY-NC-SA conditions separate from code.

05 / SOURCES

Original documentation

  1. CAD usage rights
  2. Illustrated full hand assembly
  3. Printable palm and finger components
  4. Simulation project

Found a changed specification? Submit a correction with its source ↗

← Back to the open-source index