TECHNIAHQROBOT / INDEPENDENT ROBOTICS REPORTINGENGLISH EDITION / 12 November 2026
ROBOTICS / OPEN PROJECTRobot Hands

Yale OpenHand Model T: STL Fingers, Tendons and Flexure Assembly

Yale's Model T uses one actuator to close four compliant fingers through a pulley-tree differential. It provides a practical comparison with independently motorized dexterous hands: finger contact is partly determined by the mechanics rather than joint-by-joint commands. The project includes design revisions and fabrication guides.

Editorial source check · Project documentation and public files; no physical test claimedRevision and parts availability may change
THE TECHNICAL DOSSIERYale OpenHand Model T

Why one actuator can move four fingers

The Model T's four fingers are mechanically underactuated. A floating pulley-tree differential redistributes motion when individual fingers contact objects, making the hand adaptable without four independent finger servos.

This design offers a different research target from in-hand manipulation hands. The project itself notes that a single actuator limits independent manipulation.

Printed structures and urethane flexures

The hardware repository places printable components within folders for each hand model; the original SolidWorks source also references common finger and coupling assemblies. Assembly guides distinguish pivot and flexure alternatives.

Some finger joints are fabricated using Smooth-On polyurethane and printed molds. Rigid 3D printing alone will not reproduce the compliance described in the project.

Versioned servo and tendon setup

Yale's Model T page offers multiple build revisions. The 2019 guide uses XM430 motors while earlier ones refer to MX-64. Select the hardware guide based on the actual servo.

After printing and casting, route tendons according to the differential guide, then check all four fingers with the smallest practical actuation command.

02 / FABRICATION AND ASSEMBLY

Model T tendon differential and flexure assembly

Use matching revisions of parts, firmware and instructions. These steps summarize project documentation; no physical build was performed for this article.

Assembly sequence 5 steps

  1. Choose a hand revision and servo model

    Match Model T 2.0.0 XM430 or earlier MX-64 mechanical and electrical instructions.

    Manufacturer's instructions ↗
  2. Print the palm and finger structures

    Retrieve the matching Model T meshes and any linked common coupling files.

    Manufacturer's instructions ↗
  3. Prepare the compliant joints

    Follow Yale's finger-fabrication guide for the specified urethane flexures and molded finger pads.

    Manufacturer's instructions ↗
  4. Assemble tendon differential and motor

    Route the tendons through the pulley tree and mount the Dynamixel as shown in the revision guide.

    Manufacturer's instructions ↗
  5. Check adaptive closing

    Begin with low-speed grasp trials on soft objects and inspect balanced contact between fingers.

    Manufacturer's instructions ↗
03 / PRACTICAL QUESTIONS

One-motor behavior, prints and urethane casting

Answers are based on published source material and project documentation. Their order does not represent search volume.

01Does Model T need four motors?

No. Its four fingers are driven by a single actuator through a mechanical pulley-tree differential.

Sources Official project documentation ↗

02Can I print every part from rigid PLA?

No. The compliant flexure design uses polyurethane components and molding methods described in the finger guide.

Sources Official project documentation ↗

03Which Dynamixel should I buy?

Model T has revision-specific guides: newer documentation specifies XM430 and older versions MX-64. Use the exact guide for the chosen build.

Sources Official project documentation ↗

04Why do some fingers stop moving when they touch an object?

The underactuated differential redistributes motion after contact. That is expected behavior, although uneven cable routing can also introduce friction.

Sources Official project documentation ↗

05Where are the STLs and SolidWorks assemblies?

The hardware repository stores them under model-specific folders and shared fingers/common parts. Keep referenced assembly dependencies when opening SolidWorks.

Sources Official project documentation ↗

06Can the hardware design be used commercially?

The published hardware license is CC BY-NC 3.0. It permits reuse under its noncommercial conditions and does not grant unrestricted product resale.

Sources Official project documentation ↗

04 / ENGINEERING NOTES

What to check before building Yale OpenHand Model T

Build and integration

Select Model T revision 2.0.0 or a historical revision and download its matching CAD, STL and assembly guide. Print the palm, finger and pulley structures, fabricate the urethane flexure elements as specified, mount the Dynamixel and route tendon lines through the differential. Calibrate grasp travel with no fragile object in the hand.

Known constraints

The flexure joints are not all ordinary rigid PLA prints: the process includes polyurethane casting or a compatible fabrication technique. CAD models for unrelated OpenHand models are not interchangeable. Hardware licensing is CC BY-NC 3.0, limiting commercial use.

05 / SOURCES

Original documentation

  1. All OpenHand printable designs
  2. Model T official revision and guide list
  3. Model T design files
  4. Control node and drivers
  5. Hardware terms

Found a changed specification? Submit a correction with its source ↗

← Back to the open-source index