TECHNIAHQROBOT / INDEPENDENT ROBOTICS REPORTINGENGLISH EDITION / 12 November 2026
ROBOTICS / OPEN PROJECTQuadruped Robots

Stanford Doggo: Brushless Quadruped CAD, ODrive Wiring and Setup

Stanford Doggo is a historical open quadruped notable for research demonstrations of dynamic movement. Its hardware includes CAD and a work-in-progress BOM, while the control stack uses ODrive boards and a Teensy. The maintainers have announced end of support in favor of Pupper V3.

Editorial source check · Project documentation and public files; no physical test claimedRevision and parts availability may change
THE TECHNICAL DOSSIERStanford Doggo

What the hardware release requires

Doggo uses brushless motors, custom leg links and multiple motor controllers. Its hardware folder points to a Fusion 360 CAD assembly and a BOM; the author notes that some pieces must be waterjet cut and later drilled or tapped.

The project has dependencies on Doggo and ODrive submodules. Clone with submodules before attempting to build or edit the control code.

Motor setup before locomotion

The official README describes flashing custom ODrive firmware to four controllers, running doggo_setup.py and loading the Doggo Arduino code on the Teensy. On startup the legs calibrate the motors and encoders before the idle state.

Changes to mechanical gearing require matching gear-ratio values in the controller. A mismatch can turn small setpoint errors into unsafe joint movement.

Maintenance and present-day value

The publisher has ended Doggo support while focusing on Pupper V3. Its mechanical and low-level controller sources remain a learning resource, but present-day reproductions need extra component compatibility work.

Videos of jumps or flips do not constitute an assurance of performance for a self-assembled robot. Begin with static support and cautious motor tests.

02 / FABRICATION AND ASSEMBLY

Stanford Doggo brushless legs and ODrive setup

Use matching revisions of parts, firmware and instructions. These steps summarize project documentation; no physical build was performed for this article.

Assembly sequence 5 steps

  1. Read the end-of-life notice

    Check component availability and verify whether you can still reproduce the specific historical build.

    Manufacturer's instructions ↗
  2. Obtain the full CAD and BOM

    Fetch submodules and choose matching 3D-printed, waterjet and purchased parts.

    Manufacturer's instructions ↗
  3. Manufacture and finish leg links

    Perform documented drilling and tapping after cutting where required, checking alignment before assembly.

    Manufacturer's instructions ↗
  4. Install controllers and firmware

    Wire ODrive boards and the Teensy according to the project; configure custom firmware and gear ratios.

    Manufacturer's instructions ↗
  5. Calibrate before gait trials

    Start with supported joint positions and the idle state; verify feedback and controlled travel before locomotion.

    Manufacturer's instructions ↗
03 / PRACTICAL QUESTIONS

Legacy firmware, cut parts and encoder tests

Answers are based on published source material and project documentation. Their order does not represent search volume.

01Is Stanford Doggo still maintained?

No. Its README explicitly announces end of life and directs new attention toward Pupper V3.

Sources Official project documentation ↗

02Are all structural parts 3D printed?

No. The author says some leg links require waterjet cutting, drilling and tapping in addition to printed pieces.

Sources Official project documentation ↗

03Why is my clone missing the control code?

Doggo and ODrive are submodules. Clone the repository recursively or initialize submodules at the pinned revisions.

Sources Official project documentation ↗

04Can I use stock ODrive firmware?

The official build instructions specify a custom ODrive fork. Stock firmware compatibility is not established for that historical controller configuration.

Sources Official project documentation ↗

05How do I calibrate the legs?

Flash the matching ODrive and Teensy code, run the supplied setup script and allow the startup encoder calibration as documented. Keep the robot supported during tests.

Sources Official project documentation ↗

06What happens if I change the transmission ratio?

The software must be updated to the new gear ratio; the author calls this out explicitly for modified mechanical designs.

Sources Official project documentation ↗

04 / ENGINEERING NOTES

What to check before building Stanford Doggo

Build and integration

Use the historical Fusion 360 CAD and BOM as one snapshot. Prepare 3D-printed parts and waterjet links, drill and tap required joints, install brushless drives and the Teensy, then flash the project's custom ODrive firmware. Follow the calibration sequence before using any locomotion commands.

Known constraints

This project has an explicit end-of-life notice. Some CAD parts require waterjet cutting, hole drilling and tapping rather than printing. The ODrive firmware is a project-specific fork and the source may require recursive submodule checkout; do not expect modern board firmware to be a drop-in replacement.

05 / SOURCES

Original documentation

  1. Project status notice
  2. Official assembly and setup
  3. Hardware and Fusion 360 links

Found a changed specification? Submit a correction with its source ↗

← Back to the open-source index