TECHNIAHQROBOT / INDEPENDENT ROBOTICS REPORTINGENGLISH EDITION / 12 November 2026
ROBOTICS / OPEN PROJECTQuadruped Robots

Stanford Pupper V3: four-legged robotics in the classroom

Pupper V3 is a small quadruped developed for practical robotics education. Its 12 powered leg joints, Raspberry Pi 5 computer and brushless drives let students inspect motor control and learned movement on a machine they can assemble from published instructions.

Editorial source check · Project documentation and public files; no physical test claimedRevision and parts availability may change
THE TECHNICAL DOSSIERStanford Pupper V3

A third-generation robot

Pupper V3 is different from the original StanfordQuadruped project. The older Pupper used a Raspberry Pi 4 and hobby servos; the V3 documentation specifies GIM4305 brushless actuators, three driven joints per leg and a Raspberry Pi 5. Reusing an old wiring guide or shopping list would create a hardware mismatch.

The V3 technical page lists a mass near 3 kg and a crouched body about 25 cm long, 20 cm high and 22 cm wide. Those dimensions describe the documented build rather than an arbitrary custom variant.

Reading the sensor and actuator stack

The listed sensors include a BNO086 inertial measurement unit and a wide-field camera. Motor drives report joint position, speed and effort. A student can compare that feedback to the commanded joint trajectory, then investigate why imperfect calibration or incorrect mass assumptions change the observed movement.

The repository provides a ROS 2-oriented software workspace and the documentation covers assembly, operating-system setup, operation and maintenance. The visible face display and ears add functions that are separate from leg locomotion.

Reinforcement learning and first tests

The project describes policies trained in simulation to negotiate obstacles. A new build should first pass mechanical checks, one-leg motion checks and a safe supported stance test before testing a walking policy. The published videos cannot establish the lifetime of another unit assembled with different parts.

The V3 documentation quotes about US$2,000 for a self-build. The frequently repeated US$900–1,000 budget belongs to earlier Pupper versions and should not be substituted.

02 / FABRICATION AND ASSEMBLY

Pupper V3 hardware assembly and ROS 2 bringup

Use matching revisions of parts, firmware and instructions. These steps summarize project documentation; no physical build was performed for this article.

Assembly sequence 5 steps

  1. Identify Pupper V3 before sourcing hardware

    Review the V3 mechanical and board resources. The older StanfordQuadruped/Pupper V1 guides use different parts.

    Manufacturer's instructions ↗
  2. Obtain the correct leg, chassis and electronics assemblies

    Use Pupper V3 parts from its documentation and inspect purchased motors, frame fasteners and wiring.

    Manufacturer's instructions ↗
  3. Assemble legs and route internal wiring

    Follow the matched V3 guide, verifying left/right component orientation, joint travel and cable strain.

    Manufacturer's instructions ↗
  4. Prepare Raspberry Pi and the ROS 2 workspace

    Use the documented image and matching ROS distribution; do not substitute an old V1 motor-controller sketch.

    Manufacturer's instructions ↗
  5. Check motors and stand before locomotion experiments

    With the body supported, verify individual motor response and calibration, then try a documented stable pose before policy execution.

    Manufacturer's instructions ↗
03 / PRACTICAL QUESTIONS

Version checks and the first supported standing test

Answers are based on published source material and project documentation. Their order does not represent search volume.

01Can I build Pupper V3 from the Stanford Doggo or Pupper V1 files?

No. Pupper V3 is a separate hardware generation. Use its own assembly manual, mechanical sources and compatible motor-control software.

Sources Official project source ↗

02Where are the printable robot pieces?

The hardware documentation repository is the correct starting point for V3 mechanical assets. Check the referenced release and fabrication method; a complete printable STL set is not confirmed in the software monorepo alone.

Sources Official project source ↗

03What software runs on the robot?

The Pupper V3 monorepo contains a ROS 2 workspace and physical control. Match the Raspberry Pi image and controller configuration to the same V3 hardware.

Sources Official project source ↗

04How should I approach the first standing test?

Power the robot with its body supported, verify each joint's direction and resting position, then follow the manufacturer's supported stand sequence before trying learned gaits.

Sources Official project source ↗

05Will an older $900 Pupper guide give me a current V3 budget?

No. Historic Pupper and Doggo BOM totals refer to other generations; source the V3 parts list to estimate contemporary cost.

Sources Official project source ↗

06Does the ROS software license also cover all CAD designs?

The robot software is GPL-3.0 and the documentation/hardware files have separate notices. Inspect them individually before commercial manufacturing.

Sources Official project source ↗

04 / ENGINEERING NOTES

What to check before building Stanford Pupper V3

Build and integration

Use the V3 assembly instructions and the separate public robot software repository; the older StanfordQuadruped code describes Pupper V1 and should not be treated as the V3 build source. The V3 software includes a ROS 2 workspace and a Raspberry Pi image workflow. The project documents training locomotion in simulation before deployment to the physical quadruped.

Known constraints

The older Pupper V1 budget and controller instructions do not apply to V3. The code monorepo is GPL-3.0, whereas the documentation repository carries its own license; check the license notice for each set of mechanical files before redistribution. Power and moving legs pose risks during initial calibration.

05 / SOURCES

Original documentation

  1. Official project source
  2. V3 hardware specifications
  3. Official project source
  4. Official project source

Found a changed specification? Submit a correction with its source ↗

← Back to the open-source index