TECHNIAHQROBOT / INDEPENDENT ROBOTICS REPORTINGENGLISH EDITION / 12 November 2026
ROBOTICS / OPEN PROJECTQuadruped Robots

Mini Pupper: 12-Servo Quadruped Assembly, CAD and Calibration

Mini Pupper is a Raspberry Pi-based quadruped intended for ROS navigation and legged-control experiments. The original build guide describes four leg assemblies, hip installation, servo cable lengths, body panels and calibration. Hardware variants changed over time, so choose the guide matching the production revision.

Editorial source check · Project documentation and public files; no physical test claimedRevision and parts availability may change
THE TECHNICAL DOSSIERMini Pupper

Avoid mixing the three hardware editions

The original Mini Pupper guide documents a revision change after 15 April 2022, when hip and body pieces began using molded construction. Older 3D-printable files remain relevant to some self-builds but are not identical to newer shipped kits.

Mini Pupper 2 and 2 Pro each have separate assembly instructions. Confirm the edition before choosing firmware, servo numbering or the mechanical CAD.

How four legs are assembled

The original guide builds one leg and mirrors it for the opposite side. It specifies M2 bolts, bearings and the correct direction for each link; parts that face inward on one side may face outward on the other.

Position each servo output shaft at the designated middle mark before fitting the horn. Label cable identifiers before enclosing the body, as the guide uses different cable lengths for some motor positions.

Calibration and ROS commissioning

The workflow continues from mechanical assembly to servo calibration and software installation on the Raspberry Pi. Test a supported standing pose before attempting navigation or vision modules.

Optional lidar and cameras need physical brackets and software configuration. A ROS package or accessory listing does not establish out-of-box autonomous behavior.

02 / FABRICATION AND ASSEMBLY

Mini Pupper legs, servos and body variants

Use matching revisions of parts, firmware and instructions. These steps summarize project documentation; no physical build was performed for this article.

Assembly sequence 5 steps

  1. Identify the kit revision

    Use the design reference to distinguish original Mini Pupper from the 2 and 2 Pro variants.

    Manufacturer's instructions ↗
  2. Prepare Raspberry Pi storage

    Flash the compatible operating image and collect the documented screws, bearings and servos.

    Manufacturer's instructions ↗
  3. Assemble legs and hips

    Follow left/right part orientation; align servo horns to the neutral marks and keep joints free-moving.

    Manufacturer's instructions ↗
  4. Label and connect all twelve servos

    Route the designated short and long cables to the correct connectors before installing covers.

    Manufacturer's instructions ↗
  5. Calibrate and stand

    Use the official BSP calibration tool to set leg positions, then perform low-risk standing and gait checks.

    Manufacturer's instructions ↗
03 / PRACTICAL QUESTIONS

Molded parts, calibration and ROS configuration

Answers are based on published source material and project documentation. Their order does not represent search volume.

01Can I build Mini Pupper completely from STL files?

The design reference links STL and Fusion 360 resources, but servos, bearings, fasteners, the Pi and electronic components are purchased. Later kits use molded body and hip parts.

Sources Official project documentation ↗

02Why do the build pictures not match my kit?

The original guide notes hardware changes after April 2022. A newer body may have molded parts that differ from the original prints.

Sources Official project documentation ↗

03What makes a leg move in the wrong direction?

Check whether the left/right joint orientation and servo horn center position match the manual, then run the calibration utility before testing a gait.

Sources Official project documentation ↗

04Can I use a Mini Pupper 2 guide on the first model?

No assumption of interchangeability is safe. Wiring, MCU behavior, assembly order and part inventory differ across editions.

Sources Official project documentation ↗

05How do I calibrate the 12 joints?

Install the board-support package and follow the calibrate command and official GUI or CLI process. It is version-dependent and should be completed before gait tests.

Sources Official project documentation ↗

06Does a lidar module guarantee SLAM navigation?

The accessory provides sensing hardware; the supported ROS installation and calibration still need configuration. Review the current documentation for the particular kit edition.

Sources Official project documentation ↗

04 / ENGINEERING NOTES

What to check before building Mini Pupper

Build and integration

Choose Mini Pupper original, 2 or 2 Pro before ordering or printing parts. For the original model, prepare the Pi microSD card, assemble four legs with their bearings, install and orient 12 servos, route and label cables, assemble the chassis, then calibrate every joint before commanding gait motion.

Known constraints

After April 2022, the original model moved certain body/hip parts from prints to molded parts; STL availability depends on the revision. A newer Mini Pupper 2 controller image and wiring are not necessarily compatible with an original kit. Hardware license and full cost must be checked per source package.

05 / SOURCES

Original documentation

  1. ROS and software repository
  2. Original Mini Pupper assembly
  3. Official design and STL index
  4. Software and board support
  5. Mini Pupper 2 assembly

Found a changed specification? Submit a correction with its source ↗

← Back to the open-source index