TECHNIAHQROBOT / INDEPENDENT ROBOTICS REPORTINGENGLISH EDITION / 12 November 2026
ROBOTICS / OPEN PROJECTQuadruped Robots

Solo12: Build Brushless Actuators, Assemble Legs and Calibrate Encoders

Solo12 uses twelve torque-controlled actuators and a modular mechanical architecture developed by the Open Dynamic Robot Initiative. Its repositories document motors, pulleys, encoders, printed tools, machined parts and calibration. The result is a research assembly with machining and electrical prerequisites beyond consumer 3D printing.

Editorial source check · Project documentation and public files; no physical test claimedRevision and parts availability may change
THE TECHNICAL DOSSIERSolo12 Quadruped

The mechanical work goes beyond printed parts

The project documents brushless outrunner preparation, shaft extraction, pulley fabrication, encoders and gear reductions. The mechanical tree distinguishes printed parts from machined parts.

Fabrication tolerances affect encoder and pulley alignment. The upstream motor-preparation guide describes rotor removal and reaming operations; those should be carried out only with suitable equipment.

A modular, repeatable assembly sequence

The hardware guide describes preparing motor shafts, encoders and pulleys before assembling the actuator modules. Each completed module can be tested before it is installed in a leg.

The Solo12 frame then connects twelve such actuators through three-degree-of-freedom legs. Electrical boards, cables and mechanical alignment need their respective documents.

Why encoder offsets matter

At startup the controller does not initially know absolute joint angles. The manufacturer instructs users to place legs near their zero position and find encoder index positions before adding saved offsets.

After replacing or repairing a module, its index-to-zero offset has to be measured again. Otherwise a commanded zero pose may physically correspond to a different leg configuration.

02 / FABRICATION AND ASSEMBLY

Solo12 motor modules and encoder calibration

Use matching revisions of parts, firmware and instructions. These steps summarize project documentation; no physical build was performed for this article.

Assembly sequence 5 steps

  1. Select and freeze hardware revisions

    Choose Solo12, one actuator revision and its related motor/driver components before sourcing.

    Manufacturer's instructions ↗
  2. Manufacture and inspect parts

    Prepare CNC-machined parts and 3D-printed tools; perform motor-shaft and pulley work according to upstream guides.

    Manufacturer's instructions ↗
  3. Build and test each actuator

    Install the rotor, encoder and output stages; test the module before combining mechanisms.

    Manufacturer's instructions ↗
  4. Assemble twelve joints into four legs

    Use the matching leg and chassis guides; route electronics and keep motor wiring strain-free.

    Manufacturer's instructions ↗
  5. Measure and save calibration offsets

    Use the printed calibration tools to align zero poses; re-measure offsets after repairs.

    Manufacturer's instructions ↗
03 / PRACTICAL QUESTIONS

CNC parts, print jigs and offset measurements

Answers are based on published source material and project documentation. Their order does not represent search volume.

01Can Solo12 be made with just a 3D printer?

No. The hardware project separates machined components, electronics and printable calibration parts. Motor preparation includes precision operations.

Sources Official project documentation ↗

02Where are the STL files?

The mechanics tree links printable parts, including calibration tools. The whole robot is a mix of printable and machined parts, not one STL download.

Sources Official project documentation ↗

03Why are joint positions wrong after startup?

Encoder indexing requires an offset from each mechanical zero position. Use the official calibration fixtures and saved offsets.

Sources Official project documentation ↗

04Do offsets change after actuator repair?

Yes. The official procedure says to measure and save them again whenever an actuator is repaired, replaced or modified.

Sources Official project documentation ↗

05How can I test an actuator before mounting it?

The actuator hardware project documents module testing as a separate step. Test each unit using the specified board and motor safety procedure.

Sources Official project documentation ↗

06Does the solo software repository contain mechanical CAD?

The solo repository is the low-level software interface. Use open_robot_actuator_hardware for mechanical assembly and manufacturing files.

Sources Official project documentation ↗

04 / ENGINEERING NOTES

What to check before building Solo12 Quadruped

Build and integration

Select a single Solo12 mechanical release, obtain its motors, encoders and machined pieces, then follow the actuator-module preparation sequence. Assemble and test each actuator before constructing legs and chassis. Align calibration tools to zero positions and measure encoder offsets before applying a controller.

Known constraints

Solo12 is not an STL-only build. The hardware documentation includes machined and printed parts and motor reworking steps that require precision tools. A driver installation alone cannot create a working quadruped; torque control and voltage isolation demand experienced electrical and mechanical handling.

05 / SOURCES

Original documentation

  1. Full actuator hardware tree
  2. Mechanical models and manufacturing parts
  3. Motor preparation instructions
  4. Encoder calibration and print jigs
  5. Solo low-level controller

Found a changed specification? Submit a correction with its source ↗

← Back to the open-source index