TECHNIAHQROBOT / INDEPENDENT ROBOTICS REPORTINGENGLISH EDITION / 12 November 2026
ROBOTICS / OPEN PROJECTRobotic Arms

Poppy Ergo: MX-28 Robot Arm Hardware and Python Setup

Poppy Ergo preceded the smaller Ergo Jr and uses six Dynamixel MX-28 motors rather than XL-320s. The research platform was developed at Inria's Flowers laboratory and can be controlled through pypot and Poppy's Python package. Older software and design dependencies require version-specific checks.

Editorial source check · Project documentation and public files; no physical test claimedRevision and parts availability may change
THE TECHNICAL DOSSIERPoppy Ergo

The motor family is different from Ergo Jr

Poppy Ergo's six actuators are MX-28 models. They require different electrical and mechanical considerations from the XL-320 motors used by Ergo Jr. Buying the cheaper arm's servos without changing the hardware is not a valid substitution.

The original setup uses a USB2Dynamixel or USB2AX interface with pypot. Verify both motor bus voltage and interface model before energizing the assembly.

Reconstructing a historical hardware revision

The official repository describes printable connecting pieces and links to Poppy documentation. Builders should locate the mechanical revision and its matching source assets first. A new complete STL package cannot be assumed to exist from the README alone.

Model an initial joint in CAD and confirm motor dimensions, horn mount and link spacing before duplicating parts for the full six-axis arm.

Operating and simulating the robot

The historical README recommends installing poppy-ergo and mentions V-REP. Both belong to an older software generation, so current Python or simulation versions may require compatibility changes.

Test discovery and motor limits with pypot before operating a mounted arm. Do not interpret simulator playback as evidence that a refurbished physical robot is calibrated.

02 / FABRICATION AND ASSEMBLY

Poppy Ergo MX-28 hardware and pypot setup

Use matching revisions of parts, firmware and instructions. These steps summarize project documentation; no physical build was performed for this article.

Assembly sequence 5 steps

  1. Identify the exact model revision

    Confirm the six MX-28 motors, connector hardware and published design dependencies.

    Manufacturer's instructions ↗
  2. Obtain matching mechanical models

    Locate and compare the required printable parts with the chosen revision; a complete STL bundle is not confirmed in the root repository.

    Manufacturer's instructions ↗
  3. Prepare actuator communication

    Select a supported USB2Dynamixel/USB2AX interface and test individual MX-28s.

    Manufacturer's instructions ↗
  4. Install compatible software

    Prepare Python and pypot using documented versions rather than assuming modern packages are drop-in compatible.

    Manufacturer's instructions ↗
  5. Assemble and calibrate gradually

    Install each axis and measure its direction and limits before enabling a six-joint pose.

    Manufacturer's instructions ↗
03 / PRACTICAL QUESTIONS

Historical CAD, actuator choice and Python compatibility

Answers are based on published source material and project documentation. Their order does not represent search volume.

01Is Poppy Ergo the same robot as Ergo Jr?

No. The original Ergo uses MX-28 actuators; Ergo Jr uses XL-320s and a different mechanical design.

Sources Official project documentation ↗

02Does the root repo contain all printable STL files?

The README discusses printable parts but does not provide proof of a complete revision-matched STL inventory in that root repository. Follow the official hardware references and verify files before ordering.

Sources Official project documentation ↗

03What software controls its six motors?

The original project names pypot and poppy-ergo, connected through USB2Dynamixel or USB2AX.

Sources Official project documentation ↗

04Can I run it in a modern simulator?

The README cites V-REP. A current CoppeliaSim or ROS 2 configuration is not guaranteed by the original release and may require migration.

Sources Official project documentation ↗

05Can I substitute XL-320 motors?

The published Ergo configuration is based on MX-28 units. Changing motor family also changes power, horns, bus integration and mechanics; no drop-in conversion is documented.

Sources Official project documentation ↗

04 / ENGINEERING NOTES

What to check before building Poppy Ergo

Build and integration

Start from the Poppy Ergo repository and linked hardware records; identify six MX-28-compatible motors and the proper USB2Dynamixel or USB2AX interface, then source printable connectors according to the matching project revision. Test the pypot servo connection before assembling the full chain.

Known constraints

The repository's README documents a historical research arm, not a maintained complete modern kit. It does not guarantee that every STL and fastener needed for a specific variant resides in this single repository. Original V-REP references predate the current CoppeliaSim toolchain.

05 / SOURCES

Original documentation

  1. Historic control software
  2. Poppy technology and licensing
  3. Poppy project's wider CAD resources

Found a changed specification? Submit a correction with its source ↗

← Back to the open-source index