TECHNIAHQROBOT / INDEPENDENT ROBOTICS REPORTINGENGLISH EDITION / 12 November 2026
ROBOTICS / OPEN PROJECTRobotic Arms

Poppy Ergo Jr: 3D-Print a 6-DOF Arm with XL-320 Motors

Ergo Jr is a small educational arm with six Dynamixel XL-320 actuators, a Raspberry Pi and interchangeable attachments. The Poppy repository publishes specific STL filenames and a material list. Those details make it easier to identify the correct parts before starting an assembly.

Editorial source check · Project documentation and public files; no physical test claimedRevision and parts availability may change
THE TECHNICAL DOSSIERPoppy Ergo Jr

The specific printable parts

The published bill of materials identifies base.stl, multiple horn2horn.stl and side2side.stl pieces, long_U.stl, short_U.stl and support_camera.stl. Select the gripper, lamp or pen files only for the attachment you intend to use.

Some of the historical STLs are stored through Git LFS. A tiny text pointer instead of a mesh means the file was not fetched as LFS data.

Motors, boards and fasteners

Six XL-320 servo motors carry the arm. The Poppy documentation lists a Pixl interface board, approximately 70 colored OLLO rivets, an OLLO tool, a 7.5 V supply, the Raspberry Pi and camera-related hardware.

Identify and configure motor IDs before the complete arm hides access to the motor connectors. Check the electrical pinout before connecting the power supply.

Software for classroom experiments

The original project includes Poppy software and examples. Legacy Pi image and Raspbian instructions belong to a historical hardware generation; they should not be assumed to run unchanged on recent Linux or Python.

For classroom use, verify individual joints and tool positions before moving the full arm. The swappable gripper is a demonstrator, not a rated industrial end effector.

02 / FABRICATION AND ASSEMBLY

Ergo Jr printed links and six XL-320 actuators

Use matching revisions of parts, firmware and instructions. These steps summarize project documentation; no physical build was performed for this article.

Assembly sequence 5 steps

  1. Download the correct meshes

    Open hardware/STL and select only one tool head; use the BOM quantities for repeated links.

    Manufacturer's instructions ↗
  2. Print and clean parts

    Print the base and connectors, then check rivet sockets and motor-mount dimensions.

    Manufacturer's instructions ↗
  3. Set actuator IDs

    Prepare each XL-320 before final assembly and verify wiring to the Pixl interface.

    Manufacturer's instructions ↗
  4. Assemble links and chosen tool

    Use the documented horn alignment and rivets; check joint movement manually without power.

    Manufacturer's instructions ↗
  5. Install and test Poppy software

    Prepare the Pi with a version-appropriate image, confirm servo enumeration and move one joint at a time.

    Manufacturer's instructions ↗
03 / PRACTICAL QUESTIONS

Git LFS meshes, motor IDs and interchangeable tools

Answers are based on published source material and project documentation. Their order does not represent search volume.

01Which exact STL parts should be printed?

The BOM lists one base, three horn-to-horn pieces, three side-to-side pieces and the U links, plus whichever end tool you choose. Match quantities to the official list.

Sources Official project documentation ↗

02Why is the downloaded STL only a few bytes?

Some historical CAD meshes are Git LFS objects. Download the original binary or use Git LFS rather than treating a pointer text file as printable geometry.

Sources Official project documentation ↗

03Does it need six servos or six independent motor controllers?

The official design uses six Dynamixel XL-320 motors and a Pixl board, listed separately in the materials document.

Sources Official project documentation ↗

04Can I switch between a gripper, lamp and pen?

Yes. Poppy supplies files for these different tool heads. Print and mount the chosen accessory, then check its weight and travel before operation.

Sources Official project documentation ↗

05Will an old Raspberry Pi image work on a new Pi?

The original instructions target Raspberry Pi 2/3 and an older software stack. Compatibility with newer boards is not established by that manual; test the software and OS versions first.

Sources Official project documentation ↗

06Can I sell a robot named Poppy?

The hardware is published with a share-alike license, but the Poppy name is a separately protected trademark. Commercial naming needs separate review.

Sources Official project documentation ↗

04 / ENGINEERING NOTES

What to check before building Poppy Ergo Jr

Build and integration

Print the base, paired arm links and selected tool from hardware/STL; obtain six XL-320 motors, a Pixl board, OLLO rivets, power and a compatible Raspberry Pi as listed in the BOM. Follow the Poppy assembly guide for horn orientation and links, then configure motor IDs and software on the Pi.

Known constraints

The older official instructions refer to Raspberry Pi 2 or 3 and legacy software images. Check current Python and motor-library compatibility before following historic command lines. The Poppy brand is trademarked separately from the open design files.

05 / SOURCES

Original documentation

  1. Official source repository
  2. Robot assembly guide
  3. 3D-printed structural parts
  4. Interchangeable tools
  5. Original bill of materials
  6. Editable hardware drawings

Found a changed specification? Submit a correction with its source ↗

← Back to the open-source index