TECHNIAHQROBOT / INDEPENDENT ROBOTICS REPORTINGENGLISH EDITION / 12 November 2026
ROBOTICS / OPEN PROJECTHumanoid Robots

Poppy Humanoid: the modular teaching robot from Inria

Poppy Humanoid originated in the Flowers laboratory at Inria in 2012. It has 25 Dynamixel motors and a 3D-printed structure designed to be modified in teaching and research. Its published assembly instructions remain useful, although several parts and software references reflect older hardware generations.

Editorial source check · Project documentation and public files; no physical test claimedRevision and parts availability may change
THE TECHNICAL DOSSIERPoppy Humanoid

How the project developed

Poppy was built to investigate how body morphology affects learning and movement. The platform later expanded into a community project run by Poppy Station. The open mechanical design made it possible for educators and researchers to study different link shapes and joint arrangements without designing a complete robot first.

The historical v1.0.2 specification describes an 83 cm robot weighing about 3.5 kg. Those figures describe a particular configuration, not every Poppy built from the modular files.

The assembly manual has a concrete order

Poppy’s manual covers motor identification, mounting the Dynamixel horns, assembling arms and torso, building the legs and head, and routing the wiring. Each actuator must have the correct bus ID and communication parameters before the robot is assembled around it. Fixing a wrong ID after closing a joint can mean dismantling part of the structure.

The documentation also warns that the MX-28 actuator shown in older assembly videos was superseded by the MX-28AT. Hardware substitutions are therefore worth recording alongside the assembly revision.

Why a CAD download may look empty

Some SolidWorks assets are stored with Git Large File Storage. Saving the pointer text shown by GitHub does not give you a usable design file. Obtain the tracked binary assets through Git LFS or the project’s documented release instead of treating a small downloaded placeholder as a damaged assembly.

This is one reason the published bill of materials and the mechanical archive should be checked together: an apparently complete checkout may still be missing large components.

Reuse and teaching limitations

The project lists CC BY-SA terms for hardware and GPL v3 for software; the Poppy name has separate trademark conditions. The open files support classroom modifications, but historical actuator prices and older operating-system references should not be used as a current purchasing estimate.

02 / FABRICATION AND ASSEMBLY

Poppy STL releases and the 25-motor assembly

Use matching revisions of parts, firmware and instructions. These steps summarize project documentation; no physical build was performed for this article.

Assembly sequence 5 steps

  1. Choose the head and actuator revision

    Read the head option in the BOM and identify MX-28 versus MX-28AT mounting differences before ordering hardware.

    Manufacturer's instructions ↗
  2. Download the proper CAD release

    Fetch STLs, STEP and large SolidWorks data from the official Release page or use Git LFS properly.

    Manufacturer's instructions ↗
  3. Program each Dynamixel before hiding its port

    Use the guide's motor names, digital IDs and horn orientation to prepare all 25 actuators.

    Manufacturer's instructions ↗
  4. Build arms, torso, pelvis and legs in the documented order

    Follow the 25-video sequence; keep separate left and right hip and knee IDs and inspect cable length.

    Manufacturer's instructions ↗
  5. Finish head wiring and run supported setup

    Install the chosen head and controller image, then test communication and constrained poses before attempting balance.

    Manufacturer's instructions ↗
03 / PRACTICAL QUESTIONS

CAD downloads, Dynamixel IDs and hardware revisions

Answers are based on published source material and project documentation. Their order does not represent search volume.

01Why is a SolidWorks download a tiny unreadable file?

The project stores large assets in Git LFS. Use the release archive or a full Git LFS checkout rather than a GitHub pointer file.

Sources Official project source ↗

02Where are the STL files for the robot?

The maintainer distributes STL, STEP and SolidWorks archives through GitHub Releases. The assembly BOM also links design sources.

Sources Official project source ↗

03How many actuators must I order?

The full Poppy Humanoid uses 25 Dynamixel actuators. The historical BOM is divided into legs, trunk and head; motor type differs by joint.

Sources Official project source ↗

04What is the difference between MX-28 and MX-28AT in the videos?

The official guide says MX-28 became obsolete and MX-28AT has a threaded side, changing how some nuts are installed. Follow the parts list for your motor revision.

Sources Official project source ↗

05Why doesn't a joint respond after assembly?

Confirm the digital ID, configured baud rate and bus power before loosening the mechanical joint. The manual lists specific IDs for arms, pelvis, legs and neck.

Sources Official project source ↗

06Can I use the open mechanical files in a product called Poppy?

Hardware and software use open licenses, but the Poppy project reserves the name as a trademark. Check the separate naming rights before commercial distribution.

Sources Official project source ↗

04 / ENGINEERING NOTES

What to check before building Poppy Humanoid

Build and integration

The project's materials identify 25 Dynamixel actuators and a parts list. Download CAD releases or use Git LFS when accessing large SolidWorks assets; ordinary GitHub file downloads may contain placeholders.

Known constraints

The project's cost figure is historical and depends strongly on actuator prices. The Poppy name has separate trademark restrictions even where the files use open licenses.

05 / SOURCES

Original documentation

  1. Official project source
  2. Official project source
  3. Historical platform specifications
  4. Poppy on French Wikipedia
  5. Official project source
  6. Official project source
  7. Leg subassemblies and joint IDs
  8. Torso and arm wiring details

Found a changed specification? Submit a correction with its source ↗

← Back to the open-source index