TECHNIAHQROBOT / INDEPENDENT ROBOTICS REPORTINGENGLISH EDITION / 12 November 2026
ROBOTICS / OPEN PROJECTRobotic Arms

PAROL6: STL Files, Bearings, Belt Drives and Complete Build Notes

PAROL6 resembles a compact industrial arm and publishes print files, the parts list, mechanical instructions, controller code and robot descriptions. Source Robotics warns about high-voltage hazards and experimental software. Builders should review its safety document before purchasing or energizing any parts.

Editorial source check · Project documentation and public files; no physical test claimedRevision and parts availability may change
THE TECHNICAL DOSSIERPAROL6

How the files are arranged

The repository separates the complete BOM, a Print table, STL meshes, Building instructions, PAROL6_URDF and different control-board software folders. This organization helps a builder compare the design files with the purchased items.

The BOM includes multiple bearing, belt, fastener and electronic components. The printed frame provides only part of the assembled mechanism.

Small-printer alternatives

PAROL6 provides STL/SMALL_PRINT_BED with split versions of the J1 turret piece and upper arm. The associated BOM specifies dowel pins and epoxy for joining the parts.

Do not print both the original and split variant for the same location. The joint method changes local stiffness, so inspect bonding and fit before moving the corresponding axis.

Electrical and software sequence

The source release includes control-board firmware, a GUI, a Python interface and robot-description files for simulation. Their combinations depend on the selected board and motor wiring.

Read the published safety warning before assembly. Electrical isolation, an accessible stop method and testing with no payload should precede full-speed motion.

02 / FABRICATION AND ASSEMBLY

PAROL6 STLs, split components and drive wiring

Use matching revisions of parts, firmware and instructions. These steps summarize project documentation; no physical build was performed for this article.

Assembly sequence 5 steps

  1. Read the electrical safety warning

    Determine tools, power supplies and required enclosure precautions before handling wiring or power electronics.

    Manufacturer's instructions ↗
  2. Choose print-bed configuration

    Select either the one-piece STL or officially split alternate parts and obtain the specified dowel pins and adhesive.

    Manufacturer's instructions ↗
  3. Print and source

    Prepare the frame and obtain steppers, gearboxes, belts, bearings and electronics listed in the official BOM.

    Manufacturer's instructions ↗
  4. Build and cable each joint

    Follow the mechanical instructions and check cable slack with the joint at both travel ends.

    Manufacturer's instructions ↗
  5. Verify low-level motion

    Check controller firmware, motor direction and homing before moving with a gripper or running planned trajectories.

    Manufacturer's instructions ↗
03 / PRACTICAL QUESTIONS

Small printer beds, controller setup and licensing

Answers are based on published source material and project documentation. Their order does not represent search volume.

01Do PAROL6 STL files include the control electronics?

No. The STL folder contains print geometry. The BOM lists the controller, motors, wiring, bearings and fasteners separately.

Sources Official project documentation ↗

02What if my printer bed is too small?

Use STL/SMALL_PRINT_BED. The project documents split J1 and upper-arm parts joined with dowel pins and two-part epoxy.

Sources Official project documentation ↗

03Why do the STL parts and BOM differ between versions?

Pin the revision and use its own Print table, STL set and BOM together. The public project continues to change; files from unrelated revisions can mismatch.

Sources Official project documentation ↗

04Can I run PAROL6 in ROS 2 before building hardware?

URDF and linked ROS 2/MoveIt resources are available. Simulation does not confirm real motor polarity, encoder setup or safe trajectory behavior.

Sources Official project documentation ↗

05Is the control-board design fully open?

The arm source includes controller firmware. It does not establish that every PCB manufacturing source is public; check availability before planning a completely self-fabricated electronics set.

Sources Official project documentation ↗

06What should I check before first power-up?

Read the project's high-voltage warning, verify isolation and connector polarity, then test one axis at a time in a clear workspace.

Sources Official project documentation ↗

04 / ENGINEERING NOTES

What to check before building PAROL6

Build and integration

Choose the required hardware revision and the available printer bed size. Use the BOM to source steppers, bearings, belts and fixings; the repository includes alternate STL files for small print beds. Follow the building documentation and manufacturer wiring instructions, then check each joint before enabling full motion.

Known constraints

The publisher warns that electrical hazards may cause severe injury or death. Firmware in the repository does not by itself disclose the complete proprietary board design. Mixed-version CAD, high belt loads, wrong power wiring and untuned steps can prevent a safe build.

05 / SOURCES

Original documentation

  1. Official source repository
  2. Mechanical build manuals
  3. Printable arm components
  4. Parts and fasteners list
  5. Joint and link model
  6. Safety warning

Found a changed specification? Submit a correction with its source ↗

← Back to the open-source index