TECHNIAHQROBOT / INDEPENDENT ROBOTICS REPORTINGENGLISH EDITION / 12 November 2026
ROBOTICS / OPEN PROJECTRobotic Arms

PAR6 Beta Arm: STL Files, Control Box and Assembly Guide

PAR6 is a newer Source Robotics arm intended for manipulation and robot-learning experiments. The repository includes 3D print files and an assembly manual, and lists remaining fixes to the BOM and beta documentation. The separate Robot Control Box must be included in any realistic build plan.

Editorial source check · Project documentation and public files; no physical test claimedRevision and parts availability may change
THE TECHNICAL DOSSIERPAR6 Collaborative Arm

What is actually published in the beta

The repository separates printable geometry, assembly notes, a BOM and a URDF description. The manufacturer labels the build as beta and asks users to report missing files and incorrect quantities.

Some PCB components are described as available from the vendor during the beta. A link to firmware does not guarantee that every circuit-board manufacturing asset has been released.

A two-part hardware build

Mechanical assembly covers the arm and its cable routing. The motor-control hardware lives in the separate Robot Control Box project, which has its own BOM, wiring and setup information.

Check the chosen shaft-coupler option against the alternate arm STL files: the BOM explains that one option is more prone to slipping and requires different upper-arm parts.

Commissioning with a conservative test sequence

Follow the official cable-building videos and verify connector orientation. The builder warning describes hazardous voltages, so enclosure and isolation checks are part of the build.

Only after hardware checks should the robot description be used for trajectory planning. The beta status means documented configurations may change.

02 / FABRICATION AND ASSEMBLY

PAR6 beta mechanics and its separate control box

Use matching revisions of parts, firmware and instructions. These steps summarize project documentation; no physical build was performed for this article.

Assembly sequence 5 steps

  1. Freeze one beta revision

    Check release notes, the list of missing-part issues and the BOM before printing or ordering.

    Manufacturer's instructions ↗
  2. Choose one shaft-coupler design

    Match the coupled joint hardware to the specified alternative upper-arm STL set.

    Manufacturer's instructions ↗
  3. Print and assemble arm mechanics

    Follow the official build videos, install bearings and route cables with clear movement paths.

    Manufacturer's instructions ↗
  4. Build the separate control box

    Use RCB documentation for boards, wiring and power; do not assume the arm's BOM includes this hardware.

    Manufacturer's instructions ↗
  5. Calibrate under guarded conditions

    Verify every axis and connector before moving under software control or attaching a tool.

    Manufacturer's instructions ↗
03 / PRACTICAL QUESTIONS

Parts lists, shaft couplers and beta limitations

Answers are based on published source material and project documentation. Their order does not represent search volume.

01Is PAR6 a finished production design?

The project labels itself beta. Its public list of open work includes BOM quantities, 3MF printing resources and documentation fixes. Treat a build as development hardware.

Sources Official project documentation ↗

02Do the STLs include everything needed for operation?

No. The separate Robot Control Box and its electronics are required, and the repository lists additional bought components in its BOM.

Sources Official project documentation ↗

03Which shaft coupler should I choose?

The BOM describes recommended and alternate J2/J3 couplers. The cheaper flange-style alternative is more susceptible to slipping and requires alternate upper-arm STL geometry.

Sources Official project documentation ↗

04Are all electronics manufacturing files released?

The beta BOM notes some boards as vendor-only. Inspect the RCB and driver repositories rather than assuming that every PCB and complete wiring assembly is downloadable.

Sources Official project documentation ↗

05Can I use the PAR6 description for simulation?

The repository includes robot-description resources. They describe joint geometry but cannot verify a physical build's calibration or collision behavior.

Sources Official project documentation ↗

06What electrical warning should builders read?

Source Robotics explicitly warns of hazardous voltages and the risks of a beta-stage design. Read its safety disclaimer before power work.

Sources Official project documentation ↗

04 / ENGINEERING NOTES

What to check before building PAR6 Collaborative Arm

Build and integration

Use the beta BOM and 3D Print Files folder from a pinned revision. Build the mechanical links and cables in the published video sequence, then source and assemble the separate RCB control box. Consult the beta guides for motor drivers, power and calibration before moving joints.

Known constraints

Beta repository: the publisher's open task list includes corrections to parts quantities and missing 3MF files. Some PCB modules are identified as vendor-only during the beta. Control-box components and hazardous voltages require qualified electrical work. No finished independent benchmarking is claimed.

05 / SOURCES

Original documentation

  1. Official source repository
  2. Assembly documentation
  3. Printable mechanical files
  4. Component list
  5. Separate robot control box
  6. Beta and known issues

Found a changed specification? Submit a correction with its source ↗

← Back to the open-source index