TECHNIAHQROBOT / INDEPENDENT ROBOTICS REPORTINGENGLISH EDITION / 12 November 2026
ROBOTICS / OPEN PROJECTRobotic Arms

Faze4: Printing Cycloidal Gearboxes and Assembling a 6-Axis Arm

Faze4 is a larger DIY arm that uses printed cycloidal reductions and concealed wiring. The creator reports roughly 15 kg machine mass and a parts count near 1,000 including fasteners. Those figures help explain the time needed for assembly even though the project is distributed as printable files.

Editorial source check · Project documentation and public files; no physical test claimedRevision and parts availability may change
THE TECHNICAL DOSSIERFaze4 Robot Arm

Why cycloidal gearboxes affect the build

Unlike a directly driven hobby arm, Faze4 relies on printed cycloidal reducers. A gearbox may contain many small bearings, fasteners and closely fitting printed parts; imperfect prints can cause uneven torque or backlash.

The publisher describes approximately 1,000 total parts including screws and bearings. Pre-sort hardware by joint to avoid a large pile of near-identical fasteners.

Where to start with the print archive

STL_V2.zip is the printable mesh archive. The assembly instructions and electronics PDF live elsewhere in the same repository. A STEP archive covers cycloidal disks.

Print a gearbox subset and verify its mating dimensions before committing to the remaining arm. Keep files from the same revision.

Software, wiring and reproducibility

The project includes controller software and a URDF, but moving a simulated link says nothing about the electrical safety or mechanical accuracy of an assembled arm.

Use the manufacturer electronics guide for the actual control hardware and limit first tests to low-speed joint motion without a tool. The repository does not publish an independent lifetime test.

02 / FABRICATION AND ASSEMBLY

Faze4 cycloidal disks, bearings and electronics

Use matching revisions of parts, firmware and instructions. These steps summarize project documentation; no physical build was performed for this article.

Assembly sequence 5 steps

  1. Choose the V2 mechanical revision

    Collect the STL archive and 3.1 assembly document, and check required parts from the BOM.

    Manufacturer's instructions ↗
  2. Print and test gearbox parts

    Inspect disks, bearing fits and pulley surfaces; do not force a jammed reducer.

    Manufacturer's instructions ↗
  3. Assemble the six axes

    Follow the documented base-to-wrist sequence, verifying each reduction before enclosing it.

    Manufacturer's instructions ↗
  4. Route electrical wiring

    Use the separate electronics setup guide to connect motor drivers and distribution board.

    Manufacturer's instructions ↗
  5. Configure and test

    Verify steps and directions for each axis, with no payload or loose cables near moving gears.

    Manufacturer's instructions ↗
03 / PRACTICAL QUESTIONS

Gearbox printing, firmware and license conflicts

Answers are based on published source material and project documentation. Their order does not represent search volume.

01Are the cycloidal gearboxes printed or purchased?

Faze4 is designed around 3D-printed cycloidal reducers. The print archive contains geometry; the BOM still calls for purchased bearings, fasteners and motors.

Sources Official project documentation ↗

02Where are the full STL files?

STL_V2.zip is linked from the main repository. Use it alongside Assembly instructions 3.1.pdf and the matching BOM.

Sources Official project documentation ↗

03Why does the arm have so many parts?

The creator estimates roughly 1,000 parts including screws and bearings. Gearbox internals and joint fasteners account for many small items, so sorting hardware by axis is helpful.

Sources Official project documentation ↗

04Is the license MIT or CERN-OHL?

The README says MIT, but the root LICENSE file contains CERN-OHL-S-2.0. Treat the discrepancy as unresolved and contact the maintainer before redistribution.

Sources Official project documentation ↗

05Does the original cost claim still apply?

Below $1,000 is a historical project estimate. The parts list dates from 2023 and is not an independently checked 2026 quote.

Sources Official project documentation ↗

04 / ENGINEERING NOTES

What to check before building Faze4 Robot Arm

Build and integration

Retrieve STL_V2.zip, the assembly PDF and the matching BOM; print gearbox parts carefully and inspect concentricity and clearance. Assemble in the PDF's mechanical sequence, wire the distribution board using the electronics document and perform controlled joint checks. The printed cycloidal gearboxes require special attention to fasteners and bearings.

Known constraints

The README advertises MIT while the repository LICENSE text is CERN-OHL-S-2.0; treat this as a source conflict until clarified. The advertised sub-$1,000 cost is historical. Printed gearboxes, high part count and controller assembly are advanced work.

05 / SOURCES

Original documentation

  1. Official assembly and setup
  2. STL mesh archive
  3. Assembly instructions
  4. Parts and pricing reference
  5. Controller wiring
  6. Cycloidal disk exchange model

Found a changed specification? Submit a correction with its source ↗

← Back to the open-source index