TECHNIAHQROBOT / INDEPENDENT ROBOTICS REPORTINGENGLISH EDITION / 12 November 2026
ROBOTICS / OPEN PROJECTBipedal Robots

Open Duck Mini v2: from printed legs to a walking policy

Open Duck Mini is a small, approximately 42 cm biped inspired by Disney’s BDX droids. The creator publishes mechanical parts, assembly material and reinforcement-learning experiments. Reproducing the gait involves choosing a consistent v2 hardware and software configuration.

Editorial source check · Project documentation and public files; no physical test claimedRevision and parts availability may change
THE TECHNICAL DOSSIEROpen Duck Mini

The body is only part of the build

The v2 repository includes printable pieces and a bill of materials, with the creator stating a target below US$400 for parts. This is a project estimate and does not include a verified quote for every shipping destination, the tools or the time spent on assembly.

The public repository remains a working development space. Some experiments and scripts are not presented as finished installation instructions. A builder should identify the specific revision used in a successful build before ordering servo motors or changing link geometry.

Where reinforcement learning enters

The locomotion experiments use a physics simulator to train a policy that produces joint commands. The project also shares ONNX walking policies and instructions for running them with its MuJoCo-related scripts. Training a policy in simulation and running it on real joints are separate tasks: they depend on compatible observation definitions, joint order, controller timing and safe motion limits.

The posted videos show reported progress on transferring walking behavior to the physical robot. They do not provide a standard test of survival time, speed or success over unfamiliar floors.

What to check before the first powered step

Compare the v2 print files with the servo layout, check which orientation the controller expects for each joint, then evaluate the policy in simulation. Support the robot during the first motor-power tests. Even a plausible simulated gait can put the wrong joint into a hard stop when axis conventions differ.

Who this project suits

Open Duck Mini provides a compact way to study sim-to-real locomotion with inexpensive printed mechanics. It is a stronger fit for a builder willing to debug motion and electronics than for someone seeking a finished household droid.

02 / FABRICATION AND ASSEMBLY

V2 PLA and TPU printing and biped assembly

Use matching revisions of parts, firmware and instructions. These steps summarize project documentation; no physical build was performed for this article.

Assembly sequence 5 steps

  1. Select the V2 branch and compare the BOM

    Use v2 files together; the creator links the BOM and a separate build guide. Avoid using a V1 STL in a V2 joint.

    Manufacturer's instructions ↗
  2. Print the correct PLA and TPU components

    Most V2 parts use PLA at 15% infill; foot_bottom_tpu.stl is printed with TPU at 40% to provide contact compliance.

    Manufacturer's instructions ↗
  3. Configure motors before building the frame

    The official assembly document warns to set up motors first; confirm IDs and center positions before a servo is enclosed.

    Manufacturer's instructions ↗
  4. Assemble trunk, feet, shins, thighs and hips

    Fit heat-set inserts, foot switches and bearings as illustrated; distinguish left_roll_to_pitch from right_roll_to_pitch.

    Manufacturer's instructions ↗
  5. Connect head, IMU and embedded controller

    Use the documented Raspberry Pi pin mapping, check battery cell voltage balance and only then try the published embedded runtime.

    Manufacturer's instructions ↗
03 / PRACTICAL QUESTIONS

Servo setup, mirrored hips and the walking runtime

Answers are based on published source material and project documentation. Their order does not represent search volume.

01What are the correct V2 3D-print settings?

The print guide specifies PLA at 15% infill for most components and 40% TPU for foot_bottom_tpu.stl. Check the actual printer and filament before assuming the same shrinkage.

Sources Official project source ↗

02Which foot parts must I print twice?

The V2 print guide lists foot_top, foot_side, foot_bottom_pla and foot_bottom_tpu at two pieces each. It lists mirrored links and specific repeated knee sheets separately.

Sources Official project source ↗

03Do I configure servos before or after building?

Before. The official assembly manual begins with a motor-configuration warning; otherwise the hardware may hide connectors and incorrectly centered horns.

Sources Official project source ↗

04Is the official assembly guide complete?

Not fully. The maintainer flags missing screw counts and incomplete expression-feature instructions. Cross-check the CAD and newer build guide rather than inventing a screw number.

Sources Official project source ↗

05Why are left and right hip links different?

The V2 model uses mirrored left_roll_to_pitch and right_roll_to_pitch parts. Match each hip side and the zero orientation in the illustrated guide.

Sources Official project source ↗

06Can I run the walking policy by launching MuJoCo only?

No. The repository separates training/simulation from a physical runtime for the Raspberry Pi Zero 2 W. A simulated gait does not verify servo direction, foot contact or the installed policy.

Sources Official project source ↗

04 / ENGINEERING NOTES

What to check before building Open Duck Mini

Build and integration

The repository provides separate documentation, printed parts and control experiments. Inspect the branch and component list before ordering motors or printing parts.

Known constraints

The Apache-2.0 repository license should not be assumed to override third-party component or imagery rights. Reproducing walking behavior requires additional tuning and hardware checks.

05 / SOURCES

Original documentation

  1. Official v2 project and experiments
  2. Versioned v2 README and stated cost
  3. Independent build-file index
  4. Open Duck Mini V2 printable models
  5. Official project source
  6. Official project source
  7. Motor software and v2 documents
  8. Official project source

Found a changed specification? Submit a correction with its source ↗

← Back to the open-source index