Why two arms are used
In a leader–follower setup, a person moves the leader while the follower copies its joint positions. The recorded motions can become training demonstrations when synchronized with cameras and task information. The leader therefore needs a different feel from the powered follower: it must be easy to move by hand while still reporting positions.
Hugging Face lists six STS3215 motors with 1/345 gearing for the follower. The leader uses a mix of gear ratios for joints where lower resistance matters. Interchanging these motor variants can make hand-guiding harder or change the behavior expected by the software.
Assembly starts with identification, not a neural network
The build instructions cover the bill of materials, printing, bus servo setup and mechanical assembly. Give each motor the correct address before closing the printed structure; keep a record of which servo occupies each position. A pair of arms requires two bus adapters and wiring that matches the intended leader and follower configuration.
SO-101 replaces the earlier SO-100 workflow. An old tutorial may show incompatible pieces or configuration names. Check that the printable parts, motor selection and LeRobot version refer to SO-101.
Calibration has a purpose
LeRobot provides commands to calibrate the leader and follower. Calibration aligns the recorded joint coordinates with the actual joint positions. Without it, two physically similar arms can disagree about what a particular numerical angle means, making demonstrations harder to transfer.
A first useful test is repeated movement to several accessible joint positions while checking the logged observations. Task-learning results need their own cameras, data collection and evaluation; buying the arm does not provide a trained manipulation policy.
Print and wire the SO-101 leader and follower
Use matching revisions of parts, firmware and instructions. These steps summarize project documentation; no physical build was performed for this article.
Official files and manuals 5 references
Assembly sequence 5 steps
Choose leader, follower or a matched pair
A leader uses a trigger and a follower uses a gripper; do not print both gripper-specific sets onto one assembly.
Manufacturer's instructions ↗Print the SO-101 mechanical models
The maintainer tests PLA+ at 15% infill, using a 0.4 mm nozzle and 0.2 mm layers or a 0.6 mm nozzle and 0.4 mm layers.
Manufacturer's instructions ↗Mount and configure the documented motors
Build the base, shoulder, elbow and wrist, leaving access to the Feetech bus and gripper wiring.
Manufacturer's instructions ↗Set serial ports, IDs and calibrate each arm
Use the LeRobot SO-101 setup with the correct leader/follower role; persist calibration for the actual motor set.
Manufacturer's instructions ↗Test teleoperation before recording demonstrations
Move with clear surroundings and check gripper direction and joint limits before collecting training episodes.
Manufacturer's instructions ↗
Motor calibration and leader-follower geometry
Answers are based on published source material and project documentation. Their order does not represent search volume.
01Which STL files differ between leader and follower?
SO-101 includes a leader handle, trigger and special wrist roll, while the follower uses a moving jaw and different wrist roll. Print the corresponding folder.
Sources Official project source ↗
02Which print settings were tested by the creator?
The project documents PLA+, about 15% infill and either 0.4 mm/0.2 mm layers or 0.6 mm/0.4 mm layers. Print supports and bed setup depend on the model.
Sources Official project source ↗
03Why is my SO-100 motor list wrong for SO-101?
SO-100 has been deprecated and SO-101 uses updated printed parts and motor configurations. Follow the SO-101 BOM and official LeRobot guide only.
Sources Official project source ↗
04Why do simulation gripper values not match LeRobot?
The SO-101 simulation README says the gripper mapping differs: LeRobot uses a 0–100 linear scale, while the URDF/MuJoCo models have another convention.
Sources Official project source ↗
05What if the arm moves to a strange pose after flashing?
Verify the motor role, ID, port and calibration file before increasing commands. The leader and follower mechanical zero positions differ.
Sources Official project source ↗
06Can I drive the robot in MuJoCo without buying it?
Yes, there are SO-101 URDF/MJCF models; confirm calibration conventions and geometry. The simulator does not provide measured physical payload or servo backlash.
Sources Official project source ↗
What to check before building SO-ARM101
Build and integration
The SO-ARM100 repository hosts both SO-100 and SO-101 materials. Choose the SO-101 bill of materials, printable STL files, wiring layout and assembly guide rather than mixing motor sets from the earlier SO-100 generation. A leader arm can supply human-guided joint positions to a follower arm through compatible LeRobot software.
Known constraints
The project explicitly marks SO-100 as deprecated, so older tutorials can give incompatible motor and wiring instructions. Two-arm leader–follower experiments need the corresponding hardware on both sides. Camera-based policy training requires separate camera setup and recorded demonstrations.
Original documentation
Found a changed specification? Submit a correction with its source ↗