Five actuated functions, including the gripper
The published configuration lists four arm joints plus one gripper function. ROBOTIS specifies a reach of 380 mm and a nominal payload of 500 g. Payload is not a promise that every pose, speed or tool extension can carry 500 g: motor torque demand changes with the distance between the load and each joint axis.
The documented actuator model is the DYNAMIXEL XM430-W350-T. The arm uses a serial actuator bus, so motor IDs, baud rate, operating modes and power supply setup must be coordinated before a controller can address the correct joint.
Geometry and software are separate resources
The hardware documentation includes STL files for structural components and describes modifying link lengths. A longer link changes the workspace and load on upstream joints; it also requires updating robot-description geometry before planners can produce meaningful trajectories.
The ROS packages are hosted in ROBOTIS’s open_manipulator repository, alongside materials for newer products in the same family. Choose the OpenMANIPULATOR-X instructions rather than assuming every package or tutorial addresses the same mechanism.
The current ROS 2 instructions specify Jazzy
The official quick-start guide describes a ROS 2 Jazzy workspace with DYNAMIXEL SDK, the hardware interface and the arm packages built together. It also covers serial-port permissions. Older ROS and MoveIt instructions may target different branches or message interfaces.
For a first software check, load the matching robot model and verify joint limits before connecting the arm. For a first physical motion, use low speed and check whether encoder feedback agrees with the commanded joint and its direction.
What the open files do not establish
Simulation and MoveIt examples illustrate supported software paths. They do not independently validate repeatability or gripping success under an arbitrary object, tool or trajectory. Build cost also depends on the chosen controller and actuators.
Assemble the five-XM430 arm and its gripper
Use matching revisions of parts, firmware and instructions. These steps summarize project documentation; no physical build was performed for this article.
Official files and manuals 5 references
Assembly sequence 5 steps
Collect the exact five Dynamixel actuators and chassis BOM
The manual specifies five XM430-W350-T and frame/gripper hardware plus defined 3-pin cable lengths.
Manufacturer's instructions ↗Print or source mechanical links
Use the official CAD sources and inspect bushings, rails and crank geometry before installing servos.
Manufacturer's instructions ↗Build the arm and two-finger gripper
Follow the ROBOTIS PDF/video order and route the daisy-chain bus without pinching 3-pin cables.
Manufacturer's instructions ↗Connect regulated 12 V and a supported controller
Use OpenCR or a supported PC/U2D2 setup. Verify bus communication with the exact Dynamixel IDs.
Manufacturer's instructions ↗Home and test with modest loads
Check each joint and the gripper's stroke before running ROS 2 or MoveIt, keeping below published rated constraints.
Manufacturer's instructions ↗
Dynamixel setup, STLs and replacement tools
Answers are based on published source material and project documentation. Their order does not represent search volume.
01Where are the STL models for OpenMANIPULATOR-X?
ROBOTIS provides 3D CAD links in its Assembly and Overview documentation, including Onshape/Thingiverse sources. The open_manipulator ROS repository is not the complete physical build package.
Sources Official project source ↗
02What motors and voltage are required?
The BOM specifies five DYNAMIXEL XM430-W350-T motors and the specifications list a 12 V power input.
Sources Official project source ↗
03Does the kit include the base plate?
The official Overview states that the optional base plate is not included in the normal package; account for mounting separately.
Sources Official project source ↗
04Why does the gripper or tool stop responding?
Check Dynamixel IDs, cable ordering, allowed joint ranges and tool configuration. ROBOTIS warns that out-of-range joint positions can stop operation.
Sources Official project source ↗
05Can I replace the gripper with a pen or suction tool?
Yes, ROBOTIS publishes alternate printed holders. The vacuum option also requires a pump, relay shield and a matching control sketch.
Sources Official project source ↗
06Does the 500 g rating apply at every pose and speed?
500 g is a manufacturer specification, with a 380 mm reach, rather than an independently measured payload map. Joint configuration influences actual limits.
Sources Official project source ↗
What to check before building OpenMANIPULATOR-X
Build and integration
The published ROBOTIS specifications give four arm joints plus a one-axis gripper, 380 mm reach and a 500 g payload. Its ROS 2 packages contain robot descriptions and motion-planning configurations; the official documentation describes 3D-printable mechanical parts. Start with the actuator part numbers and power supply requirements before attempting simulation-to-hardware control.
Known constraints
The 500 g payload is a manufacturer specification and should not be extrapolated to any tool pose or fast motion. The ROS package alone does not provide DYNAMIXEL motors, an OpenCR controller or 12 V power. Users need to review the individual mechanical design files before redistributing hardware assets.
Original documentation
Found a changed specification? Submit a correction with its source ↗