TECHNIAHQROBOT / INDEPENDENT ROBOTICS REPORTINGENGLISH EDITION / 12 November 2026
ROBOTICS / OPEN PROJECTMobile Robots

OpenBot: Print a Phone Robot Chassis and Connect Motors

OpenBot uses an Android smartphone for sensing and processing while a microcontroller drives the wheels. The official build guide offers four chassis geometries, two wiring paths and step-by-step printed-part assembly. Its quoted low-cost robot body excludes the smartphone and varies by component supplier.

Editorial source check · Project documentation and public files; no physical test claimedRevision and parts availability may change
THE TECHNICAL DOSSIEROpenBot

Which body fits your printer?

The regular chassis needs at least 240 × 150 mm of bed space. The slim chassis can sit diagonally on a 220 × 220 mm bed, while the glueable body is split into smaller pieces for roughly 150 × 140 mm printers.

Choose one chassis and its matching mount, not every alternative. The supplied phone holder uses separate printable top and bottom pieces.

Two wiring paths, not one universal pinout

The DIY option uses an Arduino Nano and an L298N motor board, with motor pairs and PWM pins listed in the guide. A separate custom PCB variant has different plug locations and soldering requirements.

The firmware README also specifies an OPENBOT robot-body setting. Flashing a build for another chassis or board can cause compile failures or mismatched wheel commands.

Adding the phone and first driving tests

Fit the phone securely above the chassis, connect Arduino to the handset and test joystick or gamepad control before training autonomous behavior.

Optional speed sensors, lidar-like distance sensors and LEDs need extra wiring. The published software stack depends on the Android device and the specific mode selected.

02 / FABRICATION AND ASSEMBLY

OpenBot chassis printing and motor electronics

Use matching revisions of parts, firmware and instructions. These steps summarize project documentation; no physical build was performed for this article.

Assembly sequence 5 steps

  1. Pick a bed-compatible body

    Measure your printer and download one chassis variant plus two phone-mount STL pieces.

    Manufacturer's instructions ↗
  2. Print and clean the shell

    Check motor-mount holes, wheel clearance and any glued seams before fixing electronics.

    Manufacturer's instructions ↗
  3. Install motors and chosen driver

    Solder and fasten four motors, then wire either L298N or the documented custom PCB.

    Manufacturer's instructions ↗
  4. Connect power and Arduino

    Follow the exact voltage and board pinout in the DIY manual; inspect wiring before inserting a battery.

    Manufacturer's instructions ↗
  5. Flash firmware and test Android control

    Choose the matching OPENBOT setting and board, pair with the app and test slow forward and reverse motion.

    Manufacturer's instructions ↗
03 / PRACTICAL QUESTIONS

Printer dimensions, phone mounts and firmware

Answers are based on published source material and project documentation. Their order does not represent search volume.

01How large a 3D printer do I need?

The regular body needs at least 240 × 150 mm. The slim body fits a 220 × 220 mm bed at 45 degrees, while the glueable body fits about 150 × 140 mm.

Sources Official project documentation ↗

02Can I assemble OpenBot without buying a custom PCB?

Yes. The guide has a DIY L298N/Arduino wiring option and a separate custom PCB option. Each has different connections.

Sources Official project documentation ↗

03Where are the phone-mount STL files?

The official body/diy documentation links phone_mount_top and phone_mount_bottom in STL and STEP formats.

Sources Official project documentation ↗

04Why does firmware not work with my board?

Check the OPENBOT setting and the selected Arduino Nano or ESP32 board. The firmware supports specific body/board combinations.

Sources Official project documentation ↗

05Does the $50 claim include a smartphone?

No. The project describes a low-cost robot body that uses an existing Android phone; it is not a contemporary quote for every component and the phone.

Sources Official project documentation ↗

06Is the autonomous mode ready just after assembly?

The robot can be manually driven after setup. Advanced autonomous behavior depends on software configuration, sensors, data collection and compatible Android hardware.

Sources Official project documentation ↗

04 / ENGINEERING NOTES

What to check before building OpenBot

Build and integration

Choose the regular, slim, glueable or blocky chassis based on your build plate and required electronics space. Print the body and phone mount, fit four TT motors and wheels, choose L298N wiring or an OpenBot PCB, prepare the battery circuit and load firmware for the exact board and robot-body setting.

Known constraints

The regular body requires a print area at least 240 × 150 mm; the smaller glueable variant needs 150 × 140 mm. The DIY L298N and PCB wirings differ. Autonomous driving claims depend on phone hardware, trained models and environment, not only the mechanical assembly.

05 / SOURCES

Original documentation

  1. Source project
  2. Full DIY assembly guide
  3. Printable body and phone mount
  4. Firmware and hardware variants

Found a changed specification? Submit a correction with its source ↗

← Back to the open-source index