TECHNIAHQROBOT / INDEPENDENT ROBOTICS REPORTINGENGLISH EDITION / 12 November 2026
ROBOTICS / OPEN PROJECTMobile Robots

DonkeyCar: RC Chassis Assembly, Printed Roll Cage and Calibration

DonkeyCar turns a small RC car into a camera-guided robot. Its official guide describes compatible chassis, a Raspberry Pi, camera, motor-control electronics and optional printed roll bars. Software supports driving-data collection and a simulator, but mechanical assembly and steering calibration remain separate tasks.

Editorial source check · Project documentation and public files; no physical test claimedRevision and parts availability may change
THE TECHNICAL DOSSIERDonkeyCar

A robot body based on an RC chassis

The build guide recommends selecting a supported RC car before printing attachments. The top plate and roll bar mount to that chassis; some variants need their own printed adapters and different screw lengths.

The parts list includes a Raspberry Pi, camera, battery, servo driver or HAT and fasteners. A printer-only parts calculation excludes most of the electronics.

Print and mount the camera cage

The original hardware guide describes printing a roll cage and top plate, cleaning holes and fastening the assembly to the car. Printing parameters in archived examples vary; follow the model-specific settings rather than copying a single material recipe.

A loose camera or power cable causes unstable video and sometimes mechanical steering interference. Secure these before running a drive loop.

Calibration depends on drivetrain electronics

DonkeyCar's calibration guide defines steering PWM endpoints and forward, neutral and reverse ESC values. Some L298N-style drivetrains use duty-cycle control and do not need the same throttle calibration procedure.

The current Python package uses uv-based environment setup; older tutorials may use legacy virtualenv or pip assumptions. Keep camera and package versions aligned with your Raspberry Pi OS.

02 / FABRICATION AND ASSEMBLY

DonkeyCar roll cage and RC chassis calibration

Use matching revisions of parts, firmware and instructions. These steps summarize project documentation; no physical build was performed for this article.

Assembly sequence 5 steps

  1. Choose a compatible RC chassis

    Check mounts, chassis geometry and drive electronics before selecting printed attachments.

    Manufacturer's instructions ↗
  2. Print the appropriate roll cage

    Retrieve the top plate, bar and optional chassis adapters; clean the holes after printing.

    Manufacturer's instructions ↗
  3. Install camera and compute

    Mount Pi, camera and power securely to avoid vibration or interference with steering.

    Manufacturer's instructions ↗
  4. Connect control electronics

    Wire the steering servo and ESC/driver to the appropriate board and pin mapping.

    Manufacturer's instructions ↗
  5. Calibrate and collect data

    Set steering endpoints and throttle behavior if required, then drive manually to record training data.

    Manufacturer's instructions ↗
03 / PRACTICAL QUESTIONS

STL variants, steering PWM and simulator use

Answers are based on published source material and project documentation. Their order does not represent search volume.

01Can I use any RC car chassis?

DonkeyCar supports custom builds, but printed mounts and steering connections differ. The official guide recommends several tested starting chassis.

Sources Official project documentation ↗

02Where are the STL files for the roll cage?

The hardware guide links printable roll bars, top plates and adapters. Select the files matching your car model rather than printing a generic set.

Sources Official project documentation ↗

03Why does the car steer in the wrong direction?

Check servo channel wiring and steering PWM endpoints with the DonkeyCar calibration process before changing autonomous control settings.

Sources Official project documentation ↗

04Does every drivetrain need ESC throttle calibration?

No. The official calibration guide distinguishes servo/ESC PWM from L298N differential drives that use duty-cycle control.

Sources Official project documentation ↗

05Can I train a model without a physical DonkeyCar?

The core project includes a simulator. A trained simulator policy does not guarantee safe driving on the real chassis.

Sources Official project documentation ↗

06What Python environment is required now?

The current project README uses uv and platform-specific dependencies. Older venv or camera tutorials may need updating.

Sources Official project documentation ↗

04 / ENGINEERING NOTES

What to check before building DonkeyCar

Build and integration

Choose a documented RC chassis and its fitting 3D-printed top plate and roll cage. Fit the Raspberry Pi, camera and battery, connect the steering servo and ESC or other drive electronics, then complete steering and throttle calibration before recording images or training an autonomous policy.

Known constraints

There is no single universally correct STL or motor-pin layout for every DonkeyCar; hardware depends on the RC chassis. Some archived guides contain older Pi and Python instructions while current software uses uv and a newer Python environment. A model trained in simulation needs validation on the physical car.

05 / SOURCES

Original documentation

  1. Current installation instructions
  2. Official assembly and setup
  3. Hardware and printed part guide
  4. Steering / throttle calibration

Found a changed specification? Submit a correction with its source ↗

← Back to the open-source index