How the 25 joints are distributed
The published configuration has six actuated degrees of freedom in each leg, five in each arm, one at the waist and two at the neck. The split matters for control work: a motion planner must match that joint inventory and the robot’s actual mechanical limits, rather than loading an unrelated 25-joint humanoid description.
Two onboard computers have different roles. The Radxa CM5 is assigned motion control, while a Raspberry Pi 5 handles media and networking. The README also lists CAN buses, a monocular camera, an IMU and microphones.
CAD, electrical files and fabrication
The project provides mechanical CAD, electrical schematics, PCB resources, a wiring loom and a fabrication manifest. The structure uses aluminium and nylon parts. These materials imply machining and specialist printing work for a self-sourced build, alongside ordinary assembly.
The repository includes a local fabrication-manifest check command. It helps a builder inspect the expected part inventory, but it cannot verify whether a delivered part meets dimensional or mechanical tolerances.
The cost of an unassembled kit
Menlo lists the unassembled Asimov 1 kit at US$20,000, with a US$499 reservation deposit and a final total that can vary with shipping and destination. The kit includes actuators, electronics, battery, wiring and assembly resources. Hands and workshop tools are not included in the repository’s kit breakdown, although the current sales page lists a basic Allen key set. The retail price does not establish the cost of fabricating every part independently.
Before buying components separately, compare the current BOM, the documented design revision and local fabrication quotes. Shipping, taxes and rework can change the total.
What is documented about autonomy
There is a release difference to check. The public repository roadmap still marks a locomotion policy as forthcoming, but Menlo’s current operating manual says the supplied Radxa CM5 firmware contains a walking policy for directional control on flat floors. The official Python instructions describe standing, balancing and velocity commands. Neither source publishes an independent success rate for autonomous navigation, and the full-body teleoperation interface is still under development. Check the software image shipped with a particular robot before deciding what can be reproduced entirely from public files.
Asimov 1 fabrication manifest and 25-actuator assembly
Use matching revisions of parts, firmware and instructions. These steps summarize project documentation; no physical build was performed for this article.
Official files and manuals 5 references
Assembly sequence 5 steps
Choose purchased kit or self-source
The kit includes the unassembled hardware, while self-sourcing calls for manufacturing aluminium and nylon parts plus purchasing controllers and actuators.
Manufacturer's instructions ↗Reconcile CAD, BOM and fabrication manifest
Use python3 scripts/generate_fabrication_manifest.py --check within the repository, then inspect differences before ordering.
Manufacturer's instructions ↗Set up and identify twenty-five actuators
Follow the assembly manual and assign the intended joint identities and CAN grouping before enclosing joint wiring.
Manufacturer's instructions ↗Assemble mechanical groups with power disconnected
Prepare the legs, arms, torso, neck and body following their individual manual sections; check cable routing and mechanical hard stops.
Manufacturer's instructions ↗Configure Raspberry Pi 5 and Radxa CM5 separately
Use the manufacturer's setup and test guide; inspect motor state at low load before attempting standing or walking commands.
Manufacturer's instructions ↗
Kit pricing, walking firmware and Python control
Answers are based on published source material and project documentation. Their order does not represent search volume.
01How much does Asimov 1 cost, and is the $499 deposit the full price?
Menlo lists the unassembled DIY kit at US$20,000. The US$499 amount is a reservation deposit, not the price of the robot. Menlo warns that shipping and tariffs can change the final total by destination. The cost of sourcing and fabricating every part yourself has not been independently itemized.
Sources Menlo pricing and ordering ↗
02What comes in the DIY kit, and are hands included?
Menlo lists 25 actuators, mechanical modules, a battery and charger, Raspberry Pi 5, Radxa CM5, control boards, camera and cables. The repository says hands, workshop tools, cellular modules, lidar and 360-degree cameras are outside the kit. The order page does list a basic Allen key set. Check the purchase inventory before ordering grippers or sensors separately.
03Can one person assemble it, and how long is the build?
The manufacturer estimates roughly 20 hours for assembly from its prepared kit. That is an estimate rather than a measured time for every builder. Building from raw files also requires manufacturing 7075-aluminium and MJF PA12 nylon parts, obtaining electronics and checking the wiring. Menlo's instructions require assigning all 25 actuator IDs individually before mounting them, so a missed setup step can force disassembly.
Sources Build time estimate ↗ Pre-assembly actuator procedure ↗
04Can Asimov 1 already walk, or must I train a policy?
Menlo's current manual says a locomotion policy is supplied with the Radxa CM5 firmware and supports directional walking on flat floors. Its public GitHub roadmap still labels a standalone locomotion policy as forthcoming. A kit owner may therefore receive capabilities that cannot yet be reproduced from the public repository alone. Menlo has not published an independent walking reliability benchmark for this article.
Sources Current software availability ↗ Repository release roadmap ↗
05Can I control its joints or drive it from Python?
The official menlo-sdk documentation covers robot state, balancing, velocity commands and joint control. It specifies Python 3.12 or newer and a compatible robot connection. Directional remote driving is documented; Menlo still identifies full-body teleoperation as work in progress. Start with the manufacturer's safety and setup procedures before sending motion commands to the 35 kg robot.
Sources Menlo Python SDK instructions ↗ Operation and safety ↗
06Can I test Asimov 1 without buying the physical robot?
Yes. The open project includes MuJoCo MJCF and URDF assets, and Menlo links to a browser-based simulator. These are suitable for inspecting joint geometry and experimenting with control software. Simulation alone cannot establish actuator temperatures, friction, balance reliability or real-world task success on a built machine.
Sources Simulation files and specifications ↗ Manufacturer's online simulator ↗
07How long does the battery last?
Menlo specifies a 13S4P lithium-ion battery with about 491 Wh of energy. That number is battery capacity, not operating time. The checked technical manual does not give a controlled runtime measurement for continuous walking or mixed tasks. Actual time depends on the commanded motion, carried mass, control hardware and battery condition.
08How much weight can each arm lift?
The published limits depend on the motion. Menlo lists 5 kg rated per arm for a bicep curl or front raise and 6 kg rated for a lateral raise. Peak figures reach 15 kg and 18 kg respectively, but a peak is not a sustained operating target. These manufacturer figures are not a general manipulation benchmark and assume the stated test activity.
09Can I add hands, grippers or extra sensors?
Menlo describes the wrist, head and covers as customizable, and the kit does not include hands. A builder must still check mechanical mounting, electrical supply and software integration for any attachment. Menlo's public extension manual says validated integration guidance for hands and additional sensors is still being prepared.
Sources Extension guidance and current limits ↗ Current kit exclusions ↗
10Can I reuse the CAD and software in another project?
The repository identifies CERN-OHL-S-2.0 for hardware design and GPL-2.0 for software. Those licenses have separate obligations for modifications and redistribution. Check the notices attached to the specific files and the latest license text before manufacturing or selling a derivative. A public CAD download by itself does not resolve trademark or third-party component rights.
Sources Hardware and software licenses ↗
What to check before building Asimov 1
Build and integration
Start with the fabrication manifest, BOM and mechanical release. Confirm machining access for aluminium parts and nylon fabrication, then compare wiring revisions with the onboard computing architecture: Radxa CM5 handles motion control while Raspberry Pi 5 covers media and networking.
Known constraints
Menlo says a walking policy is included in the supplied Radxa CM5 firmware, but the public GitHub roadmap still marks the standalone locomotion release as upcoming. The official manuals describe directional walking on flat floors, without an independent walking-success benchmark. Full-body teleoperation and complete robot-side training guidance remain unfinished. The $20,000 kit price is not a verified self-sourcing budget.
Original documentation
- Hardware and software licenses
- Asimov 1 construction and wiring manual
- Build time estimate
- Pre-assembly actuator procedure
- Simulation files and specifications
- Menlo Python SDK instructions
- Operation and safety
- Manufacturer's online simulator
- Battery electrical specifications
- Manufacturer's rated and peak load table
- Extension guidance and current limits
Found a changed specification? Submit a correction with its source ↗